67 barracuda/dart ...must leave

[69.5CUDA]

well my shop is well on its way in sorts.. i need to make space to move stuff around so i can build it

got a 67 fishy coupe here lil rusty but solid by east coast standards clear title if no one wants in the next week ima be cutting it up so if you want some sheet meteal lemmy know...also got some fast back skin pieces that are going to get crushed due to lack of space
SOLID frame rails and front clips

next on the chopping block will be a very solid 67 dart

 

[XLR8R]

Damn you for being where you are. DAMN YOU!

 

[mr340]

East coast standards???[smilie=e:
Rusty, you want to field this one?...

 

[Not A Duster]

So.....does either have lower brackets for bucket seats?

 

[b-body-bob]

I will need to know more about that 67 Dart when its time comes.

 

[69.5CUDA]

nad ive got you seat brakets here in a box but i thought we ran into a problem cause you had a 73+ floor meaning the drivers side has the cat hump on the floor?

as for the dart i real dont want to cut it up as the only rust is a few pin holes in the drivers side floor but no one wants to bring me 500$ for it...eventualy its going in one way or another

 

[Not A Duster]

Nope - no cat hump on the floor. I was waiting for a price - so I could send you $$$$$.

Besides the '73 is no more ....[smilie=s: .... the new car is a '72.

 

[beeper*71]

as for the dart i real dont want to cut it up as the only rust is a few pin holes in the drivers side floor but no one wants to bring me 500$ for it...eventualy its going in one way or another

Pics? [smilie=e:

 

[Jester]

Oregon isn't far from me... and it sounds a whole lot like Organ... Sweet


Me be looking for a Mopar to toy with [smilie=bunny.gif]

 

[haines]

As I was moving my67 to the new location across from the Deputy, my upper control arm left the top of the frame.
I need a ball park figure for the drivers side frame rail and inner fender plus the dreeded shipping.
Thanks.
got her going and pull out.

 

[b-body-bob]

So have you decided anything on the Dart? If you're parting it, I need rad & shroud, or at least shroud.

 

[69.5CUDA]

ive gotta move the dart in the next week or so for shop stuff at that point i will look it over and snap a ton of pics and let you all descide what i do with it....if not its being parted

haines how much frame rail are you wanting...tho it would proly be cheeper for ya to get it localy off a dart/valiant/duster as far as shipping goes

 

[chrysler300383]

Did ya get my P M i replied this morning?

 

[b-body-bob]

tho it would proly be cheeper for ya to get it localy off a dart/valiant/duster as far as shipping goes

Say, aren't the frame rails the same on all a-bodies all the way up to at least 73?

 

[69.5CUDA]

yeah actualy i thought all the way up to 76..but i know the inners are just a weeee bit diferent for smog stuff

 

[b-body-bob]

I was thinking maybe they changed it when they went to the big ball joint front end in 73. Still shouldn't be hard to find parts. Kinda like the patch pieces I need for my 67 body - any old Dart will work just fine. :beer:

 

[haines]

Thanks guy's I got a line on a 67 up here I'm going to check it out, Thanks again for the great advise.
The best nuts in the world.

 

[haines]

No luck with the one up here all ready gone.
I will keep looking.

 

[haines]

I found one in California for 75.00 for the whole front clip.
Thanks for all the help and will be asking for more.

 

[haines]

Frame rail still waiting on the ship price from Cali and I think it still might be cheaper coming from you.
Covering all the angles.
Please get back thanks.