Search results

Used them some, also a lot of mancini racing, don't know how much price checking I did but they had what I needed & seemed reasonable ?

When I was 13 or 14 an older guy moved in across the street with a 57 chevy, with a corvette 327 fuel injected engine, we used to wax the moonies for him. The start of my interest in cars. every now & then we would hunt the junk yards for parts, pick up a chrome tidbit for a couple of bucks...

It's amazing how the used prices have climbed , just from the 1st cuda to second, things doubled & tripled. I bet if I searched now they doubled again!

Do you have a tubing bending kit? I think I still have a set in the garage from my A/C days,, but honestly would have to dig around to see if it's still here. If you can use it I can get it out to you, let me know if you need & I will hunt for it. Again not positive I still have it have cleaned...

Well my seat & headliner guy is out, He didn't even want to drive an hour to do my stripe. they were father & son too! On the first car I bought 2 0r 3 different ebay lots of glass hardware, I used more on the 2nd car I guess texas heat was worse than long island salt on the plastic parts...

Moving along pretty good, bet you can't wait for that first burnout!

Too quiet around here, did you get the car back home yet?

Dad's were mostly 60's, 63 300 66 300 (that turned into my first car) 68 I think was the NYer, the imperial may have been early 70's Dad & his partner (auto parts store) got one about every three years, partner was the salesman & on the road most of the time, He got the new one, dad took the...

What model is that, my Dad had a string of chryslers back in the day, 300's NYers & one imperial!

Had to move everything around to get the snow blower ready, all mopar driveway again after the traitorous kids are all gone!

So the other day I took it out for a ride to test the heater, didn't even get out of the garage, no blower motor now, didn't check yet hoping one of the wires on the control popped off? Today I had my bro in law over to kill time while the ladies were at my sons wifes baby shower. was just...

sounds like a plan, I'll give it a try when I get brave enough to believe I won't melt the dash!!

Seat back out, my old seat foams not doing so good......................Gave that area a good clean up & while the vac was out I hit the front too. 1st page of the sheet I threw in when my son took it to work On to the retractor, pretty nasty in there, I had to pop the plastic off the rivits to...

So after wasting 1/2 hour taking trim off the front of the dash & see no way to get the heater control out I crawl under to find 3 screws from the back!!! So I fight with that for a while & get it to a position I can put the cable on the control. When I lined up the 2 cables the new looked like...

Cable has arrived, now let's see how long I put off crawling under that dang dash!

I did something like that with the hood release cable (not sure what I put down it, WD40, or just plain oil?) Anyway was thinking of oiling the new one. I did see a post on the cables, mine seemed a touch long, I had it way back at the edge of the clip, that's what popped out. but was the only...

Found the bill, bought again from same place, price the same, shipping about doubled! Should be here in a day or 2.

So the Boy also reported he had no heat, so I checked that out today, the cable popped out of the clip on the valve on the inner fender, I do remember it was right on the edge to get the full throw on the valve, so I tried slicing a hard plastic tube to extend it fully into the clip, looked like...

Now that I think about reassembly the top of the dash is held in by 4 small bolts that go in at each end of the defroster slots, so that's not it!

Looked around a bit today, checked the important stuff, gas pedal, brake pedal can't see any studs or hanging bolts with no nuts, trying to remember what the dash hold down nuts looked like, pretty sure they were studs into those lips under the windshield? (but smaller I think) Colum at floor...